Arduino
Arduino
Sort by
Show result
  • Microcontroller: ATmega2560
  • Digital I/O Pins: 54 digital input/output pins (including 15 PWM Pins)
  • Analog I/O Pins: 16 analog inputs
  • Input Voltage (recommended): 7-12V
  • Maximum Input Voltage: 6-20V
  • Clock Speed: 16 MHz 
  • DC Current per I/O pins: 40mA
  • DC Current (3.3V) : 50mA
  • Flash Memory: 256 KB (8 KB for Bootloader)
  • SRAM : 8 KB
  • EEPROM: 4 KB
  • Replacement : ATMEGA16U2 to CH340G
RM38.00
  • Atmel Atmega328P-AU microcontroller  
  • Support external 3.8V ~ 12V DC power supply 
  • Clock frequency 16MHz 
  • 20 digital input / output ports RX, TX, D2 ~ D13, A0 ~ A5 
  • 8 analog input ports A0 ~ A7 
RM11.80

Microcontroller

W5100

Operating Voltage

5V

Input Voltage (recommended)

7-12V

Input Voltage (limits)

6-20V

Digital I/O Pins

14 (of which 4 provide PWM output)

 

Analog Input Pins

6

DC Current per I/O Pin

40 mA

DC Current for 3.3V Pin

50 mA

Flash Memory

32 KB (ATmega328) of which 0.5 KB used by bootloader

SRAM

2 KB (ATmega328)

EEPROM

1 KB (ATmega328)

Clock Speed

16 MHz

RM29.50
  • Arduino Nano I/O Expansion Board comes with I/O pin output reference for easy connection.
  • Dimension: 5.2 cm x 3.6 cm x 0.1 cm
RM4.90
  • Operating Voltage(logic level):5V
  • 8 analog inputs ports: A0 ~ A7
  • 14 Digital input / output ports:TX,RX,D2 ~ D13
  • Using Atmel Atmega328P-AU MCU
RM10.80
  • ATmega 328P microcontroller
  • Operating Voltage = 5V
  • Input voltage = 7-12V (recommended)/ 6-20V (limited).
  • Output Voltage = 5V / 3.3V (50mA DC current)
  • 14 digital I/O pins (6 provide PWM output- 3,5,6,9,10,11)
  • 6 Analog Input pins (0 to 5)
  • Supply 40mA of DC current per pin
  • 16 MHz crystal oscillator (clock speed)
  • 32KB flash memory (0.5KB for bootloader/ 2KB SRAM/ 1KB EEPROM)
  • Free USB B Type Cable
RM25.50

List of item

  1. MB-102 breadboard 2
  2. USB cable
  3. Arduino UNO R3
  4. IR remote controller
  5. VS1838 IR receiver
  6. Male pin header
  7. Male to male jumper wire
  8. Male to female jumper wire
  9. Tower Pro SG90 micro servo
  10. 5V stepper motor
  11. Stepper motor driver module
  12. LM35 Temperature Sensor
  13. Red led 5mm x10
  14. Yellow led 5mm x10
  15. Green led 5mm x10
  16. Potentiometer 10K
  17. LDR light sensor
  18. 9V Battery Snap
  19. IR Receiver LED / Flame Sensor
  20. 1602 LCD display
  21. Tilt sensor
  22. Push button x4
  23. Push button cap x4
  24. Resistor 10K
  25. Resistor 1K
  26. Resistor 220R
  27. IC74HC595
  28. 5v buzzer x2
  29. Water level sensor module
  30. Sound sensor module
  31. RGB led module
  32. RTC Real time clock module
  33. DHT11 Humidity and temperature sensor module
  34. 7 segment led
  35. 4 digit 7 segment led
  36. 8x8 dot matrix display
  37. Relay module
  38. 3 axis analog joystick module
  39. RFID-RC522 module
  40. Tag for RFID module
  41. Key chain for RFID module
  42. High quality container box
RM129.00

1 Set of Arduno UNO R3 Starter Learning Kits

RM45.00
  • In the case of keeping unchanged the original master ATMEGA328P-PU replaced QFP package ATMEGA328P-AU
  • Replace the USB chip solution on the official version of the driver can not be installed on a system problem of piracy win7 win8
  • Increase the pin plug.
  • Solve the traditional UNO board is not compatible with the system in win7 and above win8 instability.
  • Increase the pin socket, to facilitate the use of DuPont line.
RM16.00
  • Microchip picoPower 8-bit AVR RISC-based microcontroller
  • 32KB ISP flash memory with read-while-write capabilities
  •  23 general purpose I/O lines
  •  internal and external interrupts
  •  the device operates between 1.8-5.5 volts.
RM15.80
  • Maker UNO X 1
  • USB Micro B Cable X 1
  • LED 5mm Red X 3
  • LED 5mm Yellow X 3
  • LED 5mm Green X 3
  • Breadboard Half Size X 1
  • Dupont 40 Pins Male to Male Jumper Wire X 1
  • Resistor 0.25W 5% (220R) X 10 
  • Resistor 0.25W 5% (1K) X 5 
  • Resistor 0.25W 5% (10K) X 5
  • LDR X 1 
  • Transistor 2N2222 X 1 
  • Finger Adjust Preset 10K X 1
  • 3V~5V DC Motor 130 X 1
  • Miniature Fan Blade X 1
  • Plastic Box X 1
RM55.00
  • Microcontroller : Atmega328P
  • Programming IDE: Arduino IDE
  • Operating Voltage : 5V
  • Digital I/O Pins: 20
  • PWM Pins : 6
  • Analog Input: 6 (10-bits)
  • UART, SPI, I2C : 1
  • External Interrupt: 2
  • Flash Memory: 32KB
  • SRAM : 2KB
  • EEPROM/ Data Flash : 1KB
  • Clock Speed: 16 MHz
  • DC current per I/O Pin 20 mA
  • Power Supply: USB Only!
  • DC Current 5V: USB Source
  • DC Current 3.3V: 500 mA
  • USB to Serial Chip: CH340G
  • Programmable LED: 12 x from digital Pin 2 to 13
  • Built in Programmable Push Button and Piezo Buzzer.
RM29.00
  • Designed to facilitate an easy connection between Arduino Nano
  • Also Compatible Arduino Duemilanove 2009 and UNO R1
  • 8 analog Pin with power output and GND
  • I2C expansion Pin
RM12.80