- Type: Emax ES08MA II
- Size: 23 x 11.5 x 24 mm (1.25 x.45 x.94in)
- Weight: 12g / 0.42oz
- Working voltage: 4.8V~6.0V
- Working current: 200mA/60°
- Four LEDs
- Three pushbuttons
- A reset button
- A piezo-buzzer
- An LED display module (four-digit, seven-segment)
- Two serial LED display driver ICs(74HC595)
- A multi-turn trimpot (10K)
- A port for DS18B20 temperature sensor
- A port for TSOP1838 infrared receiver module
- A APC220 wireless module interface (serial/UART interface)
- Type: 18650
- Nominal voltage: 3.7V
- Size: 18*65（mm）
- Nominal capacity: 2000mAh
- Master :ESP-01S
- Temperature and humidity sensor: DHT11
- Operating voltage: DC 3.7V-12V (support 3.7v lithium battery power supply)
- Measuring range: 20-90% RH 0-50 ℃
- Measurement accuracy: Temperature: ± 2 ℃ Humidity ± 5% RH
- AWG: 26
- Conductor Construction: 7/ 0.11mm
- Diameter mm: 49
- Insulator Thick: 0.41
- Over Diameter mm: 1.3
- AWG: 28
- Conductor Construction: 7/ 0.11mm
- Diameter mm: 39
- Insulator Thick: 0.41
- Over Diameter mm: 1.2
- Voltage: 1000V Maxi Peak Forward Voltage: 1000V
- Max Reverse Current : 10A
- Frequency: High Frequency
- Power: small power.
- Material: silicone, copper, plastic.
Specifications:
- Material: EVA
- Color: Orange(As Pictures Show)
- Size: 9M/15M (Approx)
- Outer diameter: 8mm (Approx)
- Inner diameter: 5mm (Approx)
Specification:
- Condition: 100% Brand New
- Item Type: Dust Blower
- Color: As picture shown
- Guns Tube Material: Stainless Steel
- Guns Handle Material: PP Plastic
- Dust Blower Piston Material: PP Plastic
- Working Pressure: 18Mpa
Specification:
- Material: Metal
- TorqueSize: 6mm
- Voltage: DC12V
- Speed:6/160/375 RPM
Specification:
- Material: Steel
- Structure: Single-side Bracket
- Size: (L*W*H) 42x40x47mm
- Screw hole diameter: about 3mm
- Application: Suitable for 555 Motor.
- Type: Terminal Type
- Model: SSR-10AA, SSR-25AA, SSR-40AA , SSR-25AA, SSR-40AA
- Rated current: 10A ,25A, 40A, 25A , 40A
Features:
100% brand new and high quality
With optocoupler isolation, the control signal and the power of the controlled device are isolated, which greatly increases the rigidity of the interference.
Compatible with MCU and Arduino control board, 3V or 5V signal.
High level start, low level stop, PWM speed regulation.
Widely used to control the start and stop of the motor, solenoid valve and other tributary equipment.
There are various specifications of MOS tube to provide choices.
E.g:
FR120N: 100V 9.4A; LR7843: 30V 161A; AOD4184: 40V 50A
The signal input side can be welded to the terminal or pin itself, compatible breadboard.
Output can be soldered to the terminal or direct wire.
Module size 23mmx16mm. There are two 2mm diameter screw holes, hole spacing 8mm.
Specification:
Optional Model: D4184/FR120N/LR7843
Color: As pictures shown.
Size: app. 23x16mm(0.91x0.63in)
Material: Electronic component
Quantity: 1 pc
Package includes:
1 x Isolated MOSFET Tube Module
- Color: Red Green Yellow Blue White
- mount Cut Lubang: 16mm
- Max Beralih Rating: AC 3A/250 V DC 5A/30 V
- contact structure: self-reset button
-
Arduino Mega/ Uno R3 Prototyping Prototype Shield with Mini Expansion Breadboard TechMakers
Description:
This prototyping shield is the best out there, and now is even better with Version R3 – updated for the most compatibility with just about all the Arduinos! It works with UNO, Mega, Leonardo, NG, Diecimila, Duemilanove, and compatible Arduino. Yun’s and Arduino Ethernets have a chunky Ethernet jack that gets in the way of stacking, you can use the stacking headers included and it will work, just doesn’t sit nice and flat.
Features:
- Prototype Shield with a compatible layout for Arduino
- Mini Breadboard with self-adhesive tape on the back, easy to stick on the Prototype Shield.
- A surface-mount chip area on Breadboard for up to 14 SOIC size parts
- One IC pattern for adding DIP ICs up to 20 pins
- It has a nice standard 0.1″x0.1″ prototyping grid with big pads
- Reset button brought to top level
- 2 general use LEDs, red and green, as well as 2 matching resistors
- Every pin is brought outExpansion Board Sensor Shield V5.0 Servo Arduino UNO R3 TechMakers
Product details:
The Arduino I/O Expansion Shield provides an easy way to connect sensors, servos and RS485 device to Arduino board. It expands Arduino’s Digital I/O and Analog Input Pins with Power and GND. It also provides separate PWM Pins which are compatible with standard servo connector. Another unique feature is that the I/O shield has a build-in RS485 converter which allows Arduino communicating with RS485 devices. The communication socket provides an extremely easy way to plug a wireless module such as APC220 RF module and DF-Bluetooth module. It has an individual power input for Servos. A servo power jumper allows user to select using external power or internal power to drive the Servos.
Features:
- Sensor Shield V5.0 allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already
- Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking
- Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language.
- Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP)
- The open-source IDE can be downloaded for free (currently for Mac OS X, Windows and Linux)
Specification:
- PIN13 LED Pilot
- Digital IO Ports D0-D13
- Analog IO Ports A0-A5
- Reset Button
- Power In
- Power LED
- SD Card Interface
- Ultrasonic Interface
- RS232 Interface(TTL)
- Bluetooth Interface
- APC220 Interface
- IIC Interface
- 12864 LCD Parallel Interface
- 12864 LCD Serial Interface