OEM
Refine Search
- Ceramic Disc Capacitor
- Single layer disc
- Resin coated
RM1.00
- All in one package for mobile project
- Chasis, gear motor and screws included
- Able to mount other modules or accessories
RM16.50
- Microcontroller: ATmega2560
- Digital I/O Pins: 54 digital input/output pins (including 15 PWM Pins)
- Analog I/O Pins: 16 analog inputs
- Input Voltage (recommended): 7-12V
- Maximum Input Voltage: 6-20V
- Clock Speed: 16 MHz
- DC Current per I/O pins: 40mA
- DC Current (3.3V) : 50mA
- Flash Memory: 256 KB (8 KB for Bootloader)
- SRAM : 8 KB
- EEPROM: 4 KB
- Replacement : ATMEGA16U2 to CH340G
Type C
Specification:
- Microcontroller Genuine ATmega2560
- CH340G replaces the Atmega16U2(USB Chip), faster
- and cheaper.
- Operating Voltage 5V
- Input Voltage(recommended) 7-12V
- Digital I/O Pins 54(of which 14 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40Ma
- Flash Memory 256KB of which 4 KB used by the
- bootloader
- DC Current for 3.3 V Pin 50 Ma
- SRAM 8 KB
- EEPROM 4KB
- Clock Speed 16MHz
- Size: 101.6mm(L) * 53.34mm(W)
RM68.00
- Ultra low-cost digital temperature and humidity sensor
- 3 to 5V power and I/O
- New data from it once every 2 seconds,
RM4.80
- Suitable for obtaining the ambient light data
- Power Supply: 3 – 5V
- Sensor Built-in: 16 bit AD converter
- Possible to detect wide range at high resolution
RM9.20
- 830 tie points
- 630 tie-point terminal strip
- 200 tie-point distribution strips
- 20~29 AWG (0.3mm ~ 0.8mm) wires
- Prototype circuit designs
RM3.70
- To detect the intensity of light.
- Resistance will become low according to the intensity of light.
- Input Voltage: DC 3.3V to 5V
- Sensitivity adjustable
RM3.20
- Operating voltage of 3.3V ~ 5V
- Rated current: <30mA
- Resonant Frequency: ~2300 Hz
- Color: Black
- Dimension: 115 x 115 x 160 mm
RM0.60
NE555 IC /JRC555
- 4.5V to 16V supply
- 8-pin DIP package
- Timing from microseconds to hours
- Adjustable duty cycle
NE555 Module
- board NE555 chip
- single-channel signal output, the output duty cycle of about fifty percent of the square wave
- onboard adjustable resistor, adjust the resistance can control the output frequency
- the onboard power indicator
- Operating voltage: 5 ~ 12V
- board size: 29 (mm) x12 (mm)
RM0.90
- Type: SPST
- Able to attach wires
- Easy to operate
- Suitable for Science or Physic Experiments in School.
- Base Dimension: 74mm x 35mm x 10mm
- Materials: Steel & Plastic
- Weight: 27g
RM2.80
- Using SW-420 normally closed type vibration sensor
- Working voltage 3.3V ~ 5V
- Output format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
RM3.20
- Resistance @25 °C: 100kΩ
- Operatiing voltage: 5V DC
- Length of Wire, approximately 8.5 cm
- Wires are tinned with solders
- Compatible with STEMSEL
RM10.50
- ISM 2.4 GHz operating frequency
- 60 mW (+18 dBm) power output (up to 750m)
- Industrial temperature rating (-40° C to 85° C)
- Indoor/Urban range: up to 300 ft (100 m)
- Outdoor/RF line-of-sight range: 750meters
- Interface data rate: Up to 115.2 Kbps
- Operating frequency: 2.4 GHz
- Supply voltage: 2.8 - 3.4 V
- Transmit current: 270 mA (@ 3.3 V)
- Receive current: 55 mA (@ 3.3 V)
- Power-down sleep current: <10 µA
- 2mm pitch to pitch DIP pin
- Wire Antenna
- Dimension: 2.438 cm x 3.294 cm
RM149.00
- Jacke : PVC
- Colou : Grey 7035
- Conducto : Bare Copper Wire Ø 0.5 mm
- Insulatior: PE, Ø 0.9mm
- Outer Diameter: 4.8mm
- Length: 1m
- Weight: 0.03kg/m
- Minimum bending radius with load : ≥ 8 X OD
- Minimum bending radius without load : ≥ 4 X OD
- Maximum tensile load, Installation Nom. : 100N
- Temperature range during operation : -20°C up to +60°C
- Temperature range during installation: : 0°C up to +50°C
RM3.00
- Length: ~100mm
- Type: Multicore wire
- Packing: 10pcs per pack
- Color Available: Red, Black and White
RM4.00