- Low cost debugger and programmer
- MPLAB IDE & MPLAB X IDE compatible
- Read/write program and data memory of microcontroller
- ISM 2.4 GHz operating frequency
- 60 mW (+18 dBm) power output (up to 750m)
- Industrial temperature rating (-40° C to 85° C)
- Indoor/Urban range: up to 300 ft (100 m)
- Outdoor/RF line-of-sight range: 750meters
- Interface data rate: Up to 115.2 Kbps
- Operating frequency: 2.4 GHz
- Supply voltage: 2.8 - 3.4 V
- Transmit current: 270 mA (@ 3.3 V)
- Receive current: 55 mA (@ 3.3 V)
- Power-down sleep current: <10 µA
- 2mm pitch to pitch DIP pin
- Wire Antenna
- Dimension: 2.438 cm x 3.294 cm
Support for multiple cascaded without hardware setup
o RGB color display and supports three kinds of mixed colors
o Dot sequence using Cartesian coordinate system, easy to understand
o Arduino development board supporting separate power supply or an external power supply
o When multiple cascading use, if the color is too dark, the supply voltage can be increased to about 5.2v. Do not exceed 5.4V
o When multiple cascading, all data lines connected to the 1st sub- board. (The origin (0,0) where the sub-board for the 1st sub-board)
List of item
- MB-102 breadboard 2
- USB cable
- Arduino UNO R3
- IR remote controller
- VS1838 IR receiver
- Male pin header
- Male to male jumper wire
- Male to female jumper wire
- Tower Pro SG90 micro servo
- 5V stepper motor
- Stepper motor driver module
- LM35 Temperature Sensor
- Red led 5mm x10
- Yellow led 5mm x10
- Green led 5mm x10
- Potentiometer 10K
- LDR light sensor
- 9V Battery Snap
- IR Receiver LED / Flame Sensor
- 1602 LCD display
- Tilt sensor
- Push button x4
- Push button cap x4
- Resistor 10K
- Resistor 1K
- Resistor 220R
- IC74HC595
- 5v buzzer x2
- Water level sensor module
- Sound sensor module
- RGB led module
- RTC Real time clock module
- DHT11 Humidity and temperature sensor module
- 7 segment led
- 4 digit 7 segment led
- 8x8 dot matrix display
- Relay module
- 3 axis analog joystick module
- RFID-RC522 module
- Tag for RFID module
- Key chain for RFID module
- High quality container box
IDC40/IDC50/IDC64 50 Male Terminal Block Breakout Board for Relay Acquisition Card Connector Wire Screw IDC 40/50/64
- Model Name: FX-888D
- Power Consumption: 70W / 220VAC
- Temperature Control: Closed-Loop Sensor
- Weight:1.2 kg
- ESD Safe: Yes
- Sensing Method: Reflective, Diffuse
- Sensing Distance: 0.079" ~ 0.984" (2mm ~ 25mm) ADJ
- Voltage - Supply: 12V ~ 24V
- Response Time: 500µs
- Output Configuration: NPN - Open Collector
- Light Source: Red LED
- Connection Method: Cable
- Ingress Protection: IP67
- Cable Length: 78.74" (2m)
- Operating Temperature: -25°C ~ 55°C
- Base Product Number: EX-14
- Broadcom BCM2837 64bit ARM Cortex-A53 Quad Core Processor SoC running @ 1.2GHz
- 1 GB RAM
- 4 x USB2.0 Ports with up to 1.2A output
- Expanded 40-pin GPIO Header
- Video/Audio Out via 4-pole 3.5mm connector, HDMI, CSI camera, or Raw LCD (DSI)
- Storage: microSD
- 10/100 Ethernet (RJ45)
- BCM43143 WiFi on board
- Bluetooth Low Energy (BLE) on board
- Low-Level Peripherals:
- 27 x GPIO
- UART
- I2C bus
- SPI bus with two chip selects
- +3.3V
- +5V
- Ground
- Power Requirements: 5V @ 2.4 A via microUSB power source
- Supports Raspbian, Windows 10 IoT Core, OpenELEC, OSMC, Pidora, Arch Linux, RISC OS and More!
- Dimensions: 85mm x 56mm x 17mm
Specification:
Note, the product comes without an AC adapter.
Can Serial Converter Product Selection Table:
RS232/485-CAN
Series | Model | Specification |
CAN to serial port | RCAN-3BT11 | 3.3V power supply, 1 TTL port, 1 CAN port |
RCAN-1C311 | 5~36V power supply, 1 CAN port, 1 RS232/485 port | |
RCAN-1C312 | 6~36V power supply, 1 port CAN, Communication isolated; 1 RS232/485 port | |
POSSIBLE for network | CANET-3B111 | 3.3 V power supply, 1 CAN port (TTL level), 1 RJ45 port |
CANET-1C111 | 5~36V powered power supply, 1 CAN port, 1 RJ45 port | |
CANET-1C112 | Power supply powered by 6~36V, 1 port box, Communication isolated; 1 RJ45 port | |
CANET-1C211 | Power powered 5~36V, 2 port box, 1 port RJ45 port | |
CANET-1C212 | Power supply powered by 6~36V, 2 port box, Communication isolated; 1 RJ45 port | |
CANET-1C221 | Power supply powered by 9~36V, 2-port box, 2-port RJ45 port; switching function; | |
CANET-1C222 | Power supply powered by 9~36V, 2-port box, 2-port RJ45 port; switching function; |
- Output Type :
- Model Number :
- DIY supplies :
RS232/485-WIFI
1) Power input: DC9~36VDC, power less than 1W.
2) Serial port rate hardware setting, support 600~460800
3) 2 serial port output signals:RS485 and RS232
4) Wireless support for AP and STA modes
5) Support DHCP Server in wireless AP mode
6) Support dynamic IP Aquisition and Static Designation
7) Support dynamic acquisition od DNS server and DNS resolution services
8) The working mode of the Module:
- TCP Server
- TCP Client
- UDP Server
- UDP Client
9) Support Web page configuration
10) Support online uprgade
11) Support Modbus TCP to RTU
- Works with ezSystem Free graphical software.
- Assumes a starting point of no electronics and/or programming knowledge
- Programmable electronic module and unique, easy to learn software
- Affordable learning kit for the young and adult.
Specifications:
1) Rainfall display range: 0 to 19,999mm
2) Outdoor temperature range: -40 ~ +65°C (-40°F to +149°F)
3) Indoor temperature range: -9.9 ~ +60°C (-15.8°F to +176°F)
4) Temperature accuracy: ±1.0°C
5) Power requirements:
a) Receiver: 2 x "AA" alkaline batteries (not included)
b) Rain gauge: 2 x "AAA" alkaline batteries (not included)
6) Transmission range: up to 100meters( 330feet)
7) Transmission frequency: 433MHz
8) Model : WH0531
Features:
1) Outdoor wireless sensor (range up to 100 meter)
2) Detail display of rainfall data in 1hour, 24hour, week, month
and total since last reset(user selectable in inch or mm)
3) Indoor and outdoor temperature (°F to °C)
4) Time and date with manual setting option
5) 12 /24 hour time mode
6) Calendar
7) Time zone setting
8) Time alarm
9) Free standing